|
Digitrax DCC |
|
Power Supplies and
Power Management
|
|
 |
PS2012 20 Amp DCC Power Supply$143.99
Regulated power supply delivers more power with less heat for more efficient
booster operation. Operate up to 4 Five amp boosters with the PS2012
supply. Scale selectable for use with N, HO or large scale. DC Ammeter. On/Off
Switch. Integral cooling fan. Design coordinated for use with Digitrax products.
|
|
 |
PS Y52 Y Cable For Ps2012 $10.36
|
|
PS 515
 |
PS 515 5 Amp
Power Supply $39.99
Recommended by Digitrax for powering Digitrax Sets & accessories. Works for DC,
too!
Fully Assembled and Ready to Run
Class 2 SELV, Input: AC120V 60Hz, Output: 15 VAC, 5 Amps, 75VA
Attach the two output leads to your DCC Booster or other device that accepts up
to 5amps 15V AC.
Plug your PS515 into an appropriate wall outlet (AC120V 60Hz).
Your PS515 is overload protected. Should you experience a power supply shut
down, simply unplug the power supply and allow at least 60 seconds for the PS515
to reset internally |
|
No
Photo |
PS 315 3 Amp Power Supply for
Zephyr Set $23.99
Recommended by Digitrax for powering Digitrax Zephyr’s DCS50. Works for DC, too!
Fully Assembled and Ready to Run
Class 2 SELV, Input: AC120V 60Hz, Output: 15 VAC, 3 Amps, 45VA
Plugs in to DCS50 via connector.
Plug your PS315 into an appropriate wall outlet (AC120V 60Hz). |
|
No
Photo |
PS 12 Amp Power Supply
AC Adapter $6.80
Recommended by Digitrax for powering Digitrax accessories
like UP5, BDL162, UR90, UR91, DS54 & PM42
Fully Assembled and Ready to Run
12V AC Adapter
Plugs into an appropriate wall outlet (AC120V 60Hz).
Overload protected
|
 |
PS 14 The PS14 is a
300ma, 14 Volt power supply for powering Digitrax accessories like the UP5,
BDL168, DS64, SE8C, LNRP, UR90 & UR91 and others
$10.36
Universal AC input 95-240V 50/60Hz
US 2 prong plug, in sideways orientation
to fit nicely on a plug strip
Stabilized output
Weight is only 2 ounces
Approximately a 4 foot long cable
Right angle, 2.1 mm center positive connector
Red LED "power on" indicator
|
|
Panels
|
|
UP5
 |
UP5 Loco Net Universal
Interconnect Panels $13.99
Simplifies hook-up, maintenance & troubleshooting of LocoNet
Give your layout a professionally finished look.
Two RJ12 6 pin LocoNet jacks in the back of the panel for hooking up LocoNet
devices that use RailSync.
Two RJ12 6 pin Throttle jacks in the front of the panel for hooking up
throttles and other LocoNet devices that do not use RailSync.
One additional RJ12 6 pin Throttle jack on the side of the panel for hooking
up LocoNet devices that do not use RailSync. For example, any device that is
not connected to other LocoNet devices beyond itself. This extra throttle jack
is great for connecting a DS54 or other local device.
Indicator LED that shows the power state of a local track section.
2mm power jack that allows you to make the UP5 a battery saver terminal for
your throttles by plugging in a PS12 DC power supply.
Rear panel has two RJ12 jacks & two #6-32 right angle screw terminals for
local track connections for power and diagnostics.
Use 6 conductor telephone cable with RJ12 6 pin male connectors on each end
and it's easy to daisy chain your network around the layout without worrying
about hooking up a lot of wires. You can use your UP5 with other Digitrax
Universal Interconnect products such as the UP1, UP2, UP3 and also with TelCo
RJ12 6 pin type jacks. Click Here for UP5 Instructions. Click here for Super
Empire Builder, see section 4.13 for more information about wiring LocoNet and
using UP5s. |
|
No
Photo |
UR 90 Infrared
Receiver $36.76
|
 |
UR91 Radio/IR Receiver Unit
$119.99
Features:
The UR91 is the radio/IR receiver unit. The UR91 looks similar to a UP5 and is
mounted in the fascia of the layout. The UR91 is simply an addition to your
existing LocoNet so no additional wiring is needed. The antennas are concealed
under the layout. The UR91 will support approximately 10 radio throttles. Most
layouts will need just one UR91 but in some large configurations a second unit
may be needed to compensate for "dead" spots. This unit is also equipped for
concurrent infrared operation using all Digitrax IR throttles, too!
|
 |
UR92 Digitrax LocoNet Duplex Transceiver Panel
$128.00
* Simplex Infrared Receiver
For Digitrax
Infra-Ready Throttles
* Duplex Radio (UR92), Simplex Radio (UR91)
and/or InfraRed (UR90) Wireless Can Be Used
Simultaneously On Any LocoNet Layout
* Range Is Approximately A 300 ft Diameter Circle
* Supports Up To 20 Digitrax Duplex Throttles
At The Same Time
* Group Name Feature Allows Multiple Clubs To
Run Independently In Close Proximity At Train
Shows and Exhibitions
* Includes PS14 Power Supply
* Operates In The 2.4 GHz Band
* Only One UR92 Is Needed To Run Duplex On
Most Layouts
|
|
Reveres
|
|
AR1 Auto Reverser
 |
AR1 Digitrax Auto Reverser
$23.99
The easiest way to add automatic reversing to a section of your layout.
8 amp Auto-reversing control for a single reversing district.
Simple to wire.
Tunable trip current lets you use it on any layout from Z to G.
AR1 operates with or without LocoNet so, it can be used on non-Digitrax DCC
systems, too. |
|
Power Management System-PM42
 |
Digitrax Power Management System-PM42
$63.99
Get the benefits of short circuit management and auto reversing without
adding more boosters!
PM42 Quad Power Manager lets you use a single booster and divide its
output into 4 power sub-districts for automatic reversing &/or to improve
operation by preempting booster shutdown when a short circuit is detected
by the PM42. If you want to improve operation but don't need the added
power (or expense) of adding a booster, the PM42 is the right answer for
you. Each PM42 can run 4 sub-districts off a single booster in any
combination of regular sub-districts and auto reversing sub-districts.
|
 |
DX-MS100 Computer Interfaces -- For
Computer w/IBM Compatible COM or RS232 Communications Port
$36.00 |
|
|
DX-LT1 Decoder And LocoNet Cable Tester
$4.95 |
Cherry Creek Hobbies
HO scale model Trains And Model
Railroad Supplies 
