|
Digitrax Detection and Signaling DCC |
 |
BD4 Quad Occupancy Detector$23.96
- Cost Effective occupancy detection for 4 detection sections
- Outputs for panel mounted LEDs to display occupancy
- Detects any powered locomotive
- Detects un-powered rolling stock equipped with resistor wheel sets
- Transmits occupancy information to your LocoNet System using DS54 or SE8C (sold
separately).
|
 |
BDL168 LocoNet Occupancy Detector
$119.99 BDL168 LocoNet Occupancy Detector for 16 detection sections
The BDL168 provides cost effective occupancy detection for 16 detection
sections. For use with one or two RX4 transponder detectors to set up 8
transponding zones and/or operations mode read back. Replaces BDL162.
- Cost effective occupancy detection for 16 detection sections
- Outputs for panel mounted LEDs to display local occupancy & power
zone status
- Connect to LocoNet to transmit occupancy information to your LocoNet
System
- Detects any powered locomotive
- Detects un-powered rolling stock equipped with resistor wheel sets
- Add one or two RX4 Transponder Receivers (sold separately) and you
can have Transponding in 8 zones. This means that you’ll know when a
detection section is occupied and the unique id of all transponders in
that section.
- Ops Mode Read Back lets you read back CV Values on any section of
track that is set up for transponding with BDL168 and one or more RX4s.
|
 |
RD2 REMOTE SENSING DIODE FOR BDL168
Remote sensing of 2 detection sections. Eliminates the need for long
runs of heavy gauge wire between the BDL16 & remotely located track sections.
$8.50 |
 |
SDCK SIGNAL DRIVER CABLE KIT
Materials for making 2 Signal Driver
Cables for SE8C. Includes 30’of 10-wire Signal Driver ribbon cable & 8 10-Pin
sockets.
Use this kit to make signal driver cables to connect your SE8c to the signals on
the railroad. Make the cables any length that you desire and place the signal
connectors at the locations where you will install signals. All the signals are
carried neatly in the ribbon cable so you can avoid a “bird’s nest” under your
layout.
$16.99 |
 |
SE8C Signal Decoder
$100.00 The Digitrax Signaling System is
organized around the concept of “security elements” which are similar to
what U.S. prototype railroads call “plants.” The Digitrax SE8C signal
decoder displays aspects for up to 32 heads for 8 individual security
elements (plants) using either a LocoNet Throttle or a computer with
compatible software. When used with associated occupancy detectors and
compatible software, the SE8C can be set up to protect the turnout as
shown by the example below. The SE8C decodes switch commands from a
throttle or associated software so that the appropriate aspects are
displayed on the signal heads.
Each security element is made up of three legs designated A, B, & C. Every
piece of track on your layout can be broken down into security elements to
describe how each detection section connects to the other sections on your
layout.
|
 |
SMBK SIGNAL MAST BASE KIT
Includes 3 Signal Masts that can be used as Signal Mast Bases in any
scale or can be painted and detailed and used as N-scale signal masts. Making
these circuit boards look like signals is easy, just paint the mast silver and
the heads black (be sure not to cover the LED with paint), then add targets and
hoods for a reasonable facsimile of a signal. Another option is to cut off the
circuit board mast from the base and attach a signal from another manufacturer
$12.75 |
 |
SMHK SIGNAL MOUNTING HARDWARE KIT
Under layout mounting hardware for Signal
Driver Cables and their sockets. 6 metal signal straps and 6 signal spacers.
These handy bits of hardware hold your signal plugs at just the right distance
from the layout to make it easy to plug in your signals.
$8.50 |
 |
TSMK SIGNAL TERMINAL STRIP MOUNTING KIT
Includes 2 terminal strip boards with
resistors for easy installation. Each terminal strip board can handle from 1 to
4 signal heads. Use this interface instead of Signal Mast Bases when you already
have signals installed on your layout. Simply run the wires from your existing
signals to the terminals on the TSMK and plug your Signal Driver Cable in on the
plug provided.
$12.75 |
